AST ACME, Inc. - Item # N-6896, Light Gray Silicone Alkyd Enamel, Type ll. Class 2, Grade B
Home
|
About Us
|
Contact Us
Call Us: 502-583-8355 | Email:
info
Coating Products:
Industrial Coatings
Military Coatings
Heavy Zinc Phosphate
Fluoropolymer Coatings
Rubber & Tank Linings
Press Releases
Learn more About
AST Acme, Inc.
-Typical Application
-Tank Linings
-Service Package
-Safety
-Capabilities
-Experience
Search Catalog
By Keyword
By Item #
All Categories
Light Gray Silicone Alkyd Enamel, Type ll. Class 2, Grade B
All Categories
>
MIL-24441 Type III Epoxy Polyamide
>
Fluoropolymer Coatings
>
MIL-P24441B, Type III Epoxy Polyamide
>
MIL-PRF-23377D, E & F Type I Class 1 Epoxy Primer
>
Light Gray Silicone Alkyd Enamel, Type ll. Class 2, Grade B
>
Item # N-6896
Printable Page
Email This Page
Save To Favorites
Item # N-6896 Light Gray Silicone Alkyd Enamel, Type ll. Class 2, Grade B
Email This Page
Save To Favorites
larger image
Intended Uses
·
Physical Properties
·
Application Characteristics
·
Recommended Primers
·
Application Equipment
·
Specifications
·
Surface Preparation
·
Shelf Life & Storage Conditions
Intended Uses
This product is a Semi-gloss copolymerized silicone alkyd enamel for use on primed, metal, gloss reinforced plastic, and plastic/composite surfaces. This product exhibits excellent color end gloss retention. This law solar absorbency (LSA) coating has been designed to be highly reflective in the near TR portion of the electromagnetic spectrum.
Physical Properties
Color
Light Grey #26373
Gloss
Semi gloss 45-60 @ 60°
Volume Solids
58.79% ± 2
Weight Solids
77.27% ± 2
Weight
12.19 ± 0.2 lb/gal
Theoretical Coverage @ 1 mil dft
943 ft²/gal
VOC
2.8 lb/gal
340 g/L
Max. Viscosity
99 KU
Substrate Tested
Product Applied on Q-Steel @ 3.0 mils DFT
Water Resistance
Pass 18 hours
Flexibility
Pass 1/8 inch Mandrel
OUV 313B
Pass 300 hours Gloss<35% ΔE<1.0 CIELAB Units
Pencil Hardness
2B @ 72 Hours
Florida Weathering (1 year)
Pass Gloss <50% ΔE <1.0 CIELAB Units
Recommended film Thickness
3 mils DFT
Application Characteristics
Mix Ratio
Single component product. Mix thoroughly before use.
Reducer
No thinning allowed
Cleaning Solvent
T-256, Mineral Spirits
Pat Life
Not applicable
Dry Time @ 77°F
Touch : 2 hrs
Through Dry : 6 - 8 hrs
Recoat 24 hrs
Full Cure
A function of time, temperature and film thickness.
Recommended Primers
Aluminum/Galvanized Steel/Stainless Steel
MIL-DLT-24441, MIL-PRF-2323C or TT-P-645
Previously Painted Surfaces Steel
Remove all mill scalene, loose rust loose paint and other foreign matter by hand or power tool cleaning (SSPC-SP2 or SSPC-SPC3 Respectively). Sand or brush blots (SSPC-SP7) hard glossy areas until dull before application.
Steel
Remove all grease oil or other surface contaminants per SSPC-SP 1. Apply over MIL-DTL 24441, MIL-PRF-23236C or TT-P-645 Printer
Application Equipment
Conventional Spray
Air Pressure
AS required for proper atomization.
Fluid Pressure
AS required for proper atomization.
Cap
Medium to heavy Visc.
Tip
2 - 3
Airless Spray
Pressure
1500 - 2500 psi
Tip
0.017-0.019
Specifications
Safety Precautions
This product is intended for professional use in an industrial environment only.
Surface Preparation
Do not apply if the surface temperature 13 less than 5°F above the dew point Before applying, the surface should be cleaned per SSPC-SP 1 to remove all surface contaminants.
Shelf Life & Storage Conditions
Shelf life : 24 months from the date of manufacture. This product must he stored in accordance with local, state, and national regulations. Keep container in a cool (35°F-95°F), dry, well- ventilated space and away from sources of heat and ignition.
Military Coatings
MIL-PRF-23377D
, E & F Type I Class 1 Epoxy Primer
MIL-PRF-24635C
Silicone Alkyd Enamel
CS 3204
Aircraft Integral Fuel Tank Sealant
MIL-PRF-22750F
High Solids Epoxy Topcoat
MIL-P24441B
, Type III Epoxy Polyamide
MIL-PRF-24667B
High Solids Non-Slip Deck Coating Type I Comp G
MIL-24441
Type III Epoxy Polyamide
MIL-PRF-85285D
Ordnance High Solids Polyurethane, Type 2, Class H
Concrete Saver®
Anti-Slip Floor Coatings Heavy Vehicle Grade
AS9100
System
Light Gray Silicone Alkyd Enamel
, Type ll. Class 2, Grade B
MIL-PRF-85285D
Two Component Tan Flat High Solids Urethane Type II
AST Acme, Inc.
| 728 South 13th Street | Louisville, Kentucky, USA 40210
Phone: 502-583-8355 | Fax: 502-583-2290 | E-mail:
info
|
Privacy Policy
|
Site Map
